Home > Hard Drive > Need Help With FDD And SATA

Need Help With FDD And SATA

Contents

Note: If your controller supports RAID, you may need to define your drive in a RAID Array before Windows will see the drive, even if the motherboard or system drivers are Even though you'll have an extra caddy, at least you'll know you have all the right parts when you go to install your drive. (And there are places that charge almost To obtain product specifications and warranty information, please contact the respective vendor directly. This information is provided as a convience to our customer - for technical assistance installing an OS, you will need to contact either your system manufactuer or the publisher of your Check This Out

I have summarized the most important points in this article. 1. Step-by-step instructions follow below: Insert the Windows 2000 CD into the CD-ROM drive and restart the system. Here are 3 ways how to reset it: http://www.wikihow.com/Reset-Your-BIOSThis is a recommended action after any hardware change you've made on your system. If you wish to add another parition to the drive, select the Disk 0 Unallocated Space again and click on New to add another new partition to the hard drive.

How To Connect Hard Drive To Motherboard

Usually, your system will display a message along the lines of “Press DEL to enter Setup.” Consult your motherboard’s manual for the correct key. For assistance with installing Windows please contact Microsoft Support. Select the drive you are writing the signature to.

If necessary install a SATA PCI card. 3. Ground yourself, either by wearing an antistatic wrist strap, or by touching grounded metal. 3 Access the old hard drive. About this wikiHow How helpful is this? Sata Power Connector You could have one drive set as C and D, and the second physical drive might be E drive.

If this is the case, you will need to use a Molex-to-SATA adapter. 5 Connect the optical drive to the motherboard. How To Connect Sata Hard Drive To Motherboard The method will vary depending on your laptop model. If your system does not have a Serial ATA connector on the motherboard, you must purchase a Serial ATA host adapter that is compatible with your computer and operating system and EDIT Edit this Article Home » Categories » Computers and Electronics » Hardware » Internal Components » Hard Drives ArticleEditDiscuss Edit ArticlewikiHow to Install a SATA Drive Three Methods:Installing a Desktop

Connected directly to a Serial ATA connector on the motherboard Unlike EIDE cables, either end of a standard SATA cable can be connected to the drive. Sata Power Cable If using FAT32, don’t create anything larger than 32GB. After that I called the E-Store hotline, they confirmed that none of the cables will work in my situation. Some enthusiast-class also cases give users the ability to remove drive cages or to mount them in different positions to optimize air flow and simplify cable management.

How To Connect Sata Hard Drive To Motherboard

Your computer may automatically detect your new drive. Most laptops only have one hard drive slot, so if you replace your hard drive you will lose access to all of your old data. How To Connect Hard Drive To Motherboard Best answer SuperSoph_WDDec 5, 2014, 3:44 PM Have you head any Windows updates lately as well?This error often occurs when crucial software changes have been made to the OS. Sata Hard Drive Power Cable That way, you can easily boot from a CD or DVD without altering the BIOS settings, but it might add a few seconds to the boot time while the optical drive

If the power supply is older, it may not have any SATA power connectors. Click on New to add a new partition to the hard drive. Select the drive you are writing the signature to. In the BIOS, go to the standard System Settings menu or the Integrated Peripherals > SATA menu to see all of the drives installed in the system. Sata Interface Cable

Preview post Submit post Cancel post You are reporting the following post: Need help installing XP on SECOND SATA hard drive This post has been flagged and will be reviewed by You need more than just a cable. Let me clarify, I moved the Sata connector to a different port and it recognized my Hard drive as a New Hard drive and basically it wants me to Format the http://apksoftware.com/hard-drive/my-2nd-sata-hdd-is-listed-as-a-removeable-device.html Every drive is essentially the same, but this means you need to tell the motherboard's BIOS which drive to boot from.

Locate the HDD you wish to replace and disconnect each of the two cables coming out from the rear of the drive. Sata Connector To Usb pfff! Some operating systems do not configure themselves to load the AHCI driver upon boot if the SATA-drive controller was not in AHCI mode at the time of installation.

I saw this on PC Advisor and thought you should see it too.

Match pin 1 on the IDE interface cable to the connector on the motherboard. What you need is the SATA interface cable (red cable in image above) and either a 4-pin Molex power connector or a SATA power cable. Book your tickets now and visit Synology. Sata Data Cable Many cases—especially enthusiast cases—use tool-less trays that hold the drives with simple pins and clips.

Format your new storage drive. You will need to install a new motherboard if you want to use your SATA drive. 6 Finish the installation. Start Windows XP and allow the Operating System to boot to the desktop. http://apksoftware.com/hard-drive/need-help-transferring-files-from-ide-hard-drive-to-sata-hard-drive.html If it’s a SATA drive, double-check whether another SATA connector is available on the motherboard, given you want to keep the old hard drive installed.

Leave the allocation unit size at default and label the drive as desired. This may damage the drive. I OWE MY SANITY TO XXCLONE!This thing backup up my whole drive and WORKED in under 10 minutes flat with no extra work from me at all.Oh, and by the way, The next image shows part of a motherboard with two SATA connectors (purple).

Taken together, you need to consider the following: You need one SATA interface cable for each SATA hard drive. Connect the data cable to the smaller SATA port on the hard drive. Ready to upgrade your hard drive? If all of your drive controllers are enabled and the drive is properly connected (and functional), it should be listed in the BIOS.  If the drive isn’t listed, shut down your

Western Digital highly recommends partitioning your drive in this manner. This will help keep you grounded. If you want a single partition (single drive letter), select all the available disk space. Select your primary (C:) partition and press ENTER on your keyboard to begin installing Windows XP.

I just purchased mine so the are in stock there. The SATA cables they sell are for desktops rather than notebooks. I saw this on PC Advisor and thought you should see it too. Once the hard drive is secured and connected, close up your computer and power it back on.

Make sure to only use short screws designed for hard drives; if the screws are too long they could seriously damage the hard drive when it is running. 8 Connect the If the drive still is not detected after testing the cables, contact your controller card manufactuer to see if there is an update available. Troubleshooting If your drive is not working properly, please visit the SATA Hard Drive Troubleshooting A great first step is to download SeaTools diagnostic software.   REFERENCE TO THIRD PARTIES AND