Proffitt Forum moderator / July 19, 2005 8:43 AM PDT In reply to: Mixing SATA and IDE drives in a system? My 40 GB hard drive only show up as 38.2 GB: The formatted space will always be a bit less than the advertised storage capacity. OSNews.com uses icons from the Tango Project and FamFamFam. BUY NOW FREE TRIAL Todo Backup Advanced Server Windows server, exchange and SQL Server backup solution to ensure business continuity. Check This Out
You must be sure to set the jumpers to master and slave, this should be identified by the diagram on the drive.I am using the appropriate cables for each drive.You will The next step is to gently slide the device into the empty bay (fig 1.4) making sure it is free of any obstruction. If you are replacing the IDE drive with a SATA device then you can unplug the IDE cable from the motherboard. Advertisement On the motherboard end, the socket looks like this.
I have Windows 2000 with an AMD 2800 chip and A7V8X mobo. Initialize the drive. A wizard will pop up and walk you through this process.
Write out a quick table to figure out how it is currently set up, like this: CHANNEL 1, MASTER: CHANNEL 1, SLAVE: CHANNEL 2, MASTER: CHANNEL 2, SLAVE: Probably your hard by RJSheppard / July 23, 2005 1:30 AM PDT In reply to: Mixing SATA and IDE drives in a system? When you are inserting the screws do not tighten them completely until you have all of the screws inserted, this will make it easier to align each screw. How Many Hard Drives Can Be Connected To A Single Ide Cable Master should be selected if this will be the only device on a single IDE cable or if it is the second device to be connected and the other device is
Nothing showed in Windows XP at all-didn't show up in disk management either. Sata And Ide Hard Drives Together Wonder what connects to where on the cable? BUY NOW FREE TRIAL PARTITION MANAGER For Business » Partition Master ProfessionalBuyTry Partition Master ServerBuyTry Partition Master UnlimitedBuyTry For Home & Home Office » Partition Master FreeDownload Partition Master ProfessionalBuyTry For This second drive will only have data.
So, to make it a slave device, I place a jumper over the central (second) pair. Ide And Sata Drives In Same Computer I'll double check the motherboard drivers but I'm sure the one's I've got are up to date. You can also push the blank out from the inside of the case with your fingers, but be careful not to loosen anything within the case while you do it. If they aren't then you've got some troubleshooting to do.
I'm looking for a USB 2.0 to the correct IDE type of cable so I can transfer onto either my computer or another notebook. Again, thanks and appreciate the help. How To Connect Ide Hard Drive To Sata Motherboard solved Can a USB IDE Hard Drive enclosure be converted to SATA? Ide Hard Drive Jumper Settings BUT BEWARE one thing.
SATA stands for Serial Advanced Technology Attachment. Boards with mulitple SATA connectors and a single PATA connector are still around. BUY NOW FREE TRIAL BACKUP & RESTORE For Business » Todo Backup WorkstationBuyTry Todo Backup ServerBuyTry Todo Backup Advanced ServerBuyTry For Home & Home Office » Todo Backup FreeDownload Todo Backup Computer motherboard help and support. 2. How To Connect Ide Dvd Drive To Sata Motherboard
When two drives share one cable, you give them different names. By the way, what are the short pci express slots for? Reply James Bruce November 18, 2015 at 8:16 pm if you only have 1 IDE channel on your motherboard, then you're out of luck. Flag Permalink This was helpful (0) Collapse - Mixing SATA and IDE drives in a system?
It's also a good idea to touch the power supply before you go sticking your hands in there! Ide To Sata Connector This article discusses the options. Hard disks have passed through a long evolution of connectivity and data transfer standards.
One end of the SATA cable plugs into this and the other end plugs into the device. I'm using 3 maxtor HD's 80 & 120 gb sata + 200 gb pata, and 3 dvd burners BENQ 1625, & 1610, + LG GSA 4163B. That mistake recognized and rectified, I still cannot figure out why XP won't load under my current setting.The BIOS settings have been set so that SATA 0 is the drive to Motherboard With Ide And Sata Ports CompTIA_RepMay 6, 2011, 6:36 AM Your welcome!
Flag Permalink This was helpful (1) Collapse - It's about reading mobo doc and following instructions by Doug_Hirschfeld / July 28, 2005 11:10 AM PDT In reply to: It's all about Therefore most people can run 6 devices note that each sata connector MUST NOT be shared you may only connect 0 - 2 sata devices and 0 - 4 IDE devices.If Subscribe to Our Newsletter Email: Advertisement Scroll down for the next article © 2017 MakeUseOf. Flag Permalink This was helpful (0) Collapse - Feel free to make a new post.
It sees any other IDE drive attached, but not the HDD. If you have an IDE drive, whether it is a hard drive or CD/DVD drive, and your motherboard has a SATA connection, you can still connect the IDE drive to the In the image you can see a typical SATA connector on a motherboard. Articles & News Forum Graphics & Displays CPU Components Motherboards Games Storage Overclocking Tutorials All categories Chart For IT Pros Get IT Center Brands Tutorials Other sites Tom's Guide Tom's IT
Be sure to follow any instructions about the jumpers on the IDE drives. Convert all partitions on IDE HDs to extended. (This option maybe optional)2. To its right is the SATA power plug. Proffitt Forum moderator / December 7, 2006 5:45 AM PST In reply to: SATA & IDE Combination Troubles--but w/ SATA adapters IDE's But I'll decline why since this post is buried
The case screws are bigger than the ones used to screw in your CD drives. Many transition motherboards manage PATA and SATA drives together just fine. First of all Master, Slave? You can find this adapter at a number of retail and online stores, including Best Buy, Walmart, TigerDirect, and Amazon.com.
Transition Drive Uses Either Power Plug (Gateway) Inspect your motherboard, too.