Home > Hard Drive > Need QUICK Help Connecting My Hard Drives And Cd Rom

Need QUICK Help Connecting My Hard Drives And Cd Rom

Contents

Generally it's the [del] button that gets you into the BIOS but sometimes it's F1 or F2. Inicia sesión para que tengamos en cuenta tu opinión. Cargando... My System Specs You need to have JavaScript enabled so that you can use this ... navigate here

Get the answer mang0zApr 12, 2013, 7:29 AM I was confused earlier. hope it help you.

WOW! You need to shut down and then start your PC again for fast startup to take effect. Now when i plug in my external hard drive to my computer or laptop, it is reading my hard drive as a Virtual CD-rom, and I can only access a handful

Ide Hard Drive Jumper Settings

If you plan on installing Windows NT or Windows 2000 you can utilize the Windows NT setup to create a NTFS partition or FAT32 partition if using Windows 2000. I was restarting the computer when the matter referenced in the thread title happened. BUY NOW FREE TRIAL UTILITIES PC Transfer » Todo PCTrans FreeDownload Todo PCTrans ProBuyTry Todo PCTrans TechnicianBuyTry Disk/Partition Copy » Disk Copy HomeDownload Disk Copy TechnicianBuy File Sync EverySyncBuyTry System Optimization Can't find your answer ?

The time now is 02:59. Open Computer Management and select Disk Management. Today, all IDE/EIDE and SATA hard drives are 3.5-inch. How To Install Ide Hard Drive Reply Shayan November 18, 2015 at 6:19 pm what to do if i use 2 IDE hard disk instead of a CD-ROM?

Do you have only one entry in the list there? are a legend... 6 hours of me trying to figure this out and an angry mrs.. it has no connections or anything electronic.I'm pretty sure this is the model I have: http://www.amazon.com/Passport-Essential-Portable-External-Midnight/dp/B0041OSAZS/ref=pd_sim_sbs_e_3/184-1181466-7559051 There's actually a 2.5" SATA hard drive in that case connected to a SATA to If you plan on using another operating such as Linux or Unix, disk partitioning will be performed during the installation process.

More by StevenTyler:Add instructable to: Contest GroupFEATURED CHANNELSWoodworkingPaperKitchen HacksPuzzlesLaser CuttingSpaceHomesteading3D PrintingSewingNewsletterJoin 2 million + to receive instant DIY inspiration in your inbox.I'm in!About UsWho We AreAdvertiseContactJobsHelpFind UsFacebookYoutubeTwitterPinterestGoogle+ResourcesFor TeachersArtists in ResidenceGift Premium Seagate Ide Hard Drive Jumper Settings Elige tu idioma. My System Specs You need to have JavaScript enabled so that you can use this ... The hard drive doesn't even power up: Check to make sure the IDE cable is connected correctly.

How To Connect Ide Hard Drive To Motherboard

Vuelve a intentarlo más tarde. This method has allowed me to install a nice fresh edition of OS on new hard drive with having to send laptop to Toshiba for unlock. Ide Hard Drive Jumper Settings With a new case you should be able to save all your data. How To Connect Ide Hard Drive To Sata Motherboard Inicia sesión para que tengamos en cuenta tu opinión.

Troubleshooting If additional issues are encountered during or after the installation of the hard drive, refer to our main hard drive page for additional help and information. check over here An unused drive power cable for your new drive. Thnx a lot ??

My laptop display is broken. Once you're in the BIOS you'll want to go into standard CMOS where you should see something like this: Run the system setup program. How Many Hard Drives Can Be Connected To A Single Ide Cable

If this is the only hard drive it is recommended that the drive be connected to PRIMARY 0, PRI 0, PRIMARY 1 or PRI 1. Troubleshooting No hard drives show up: Do you have two drives on the cable? Additional information How to install computer hardware. http://apksoftware.com/hard-drive/need-help-with-ide-drives.html And here one thing to note is that it is preferred to have the CD-ROM and other non-hard drive products on the secondary ATA channel.

I did that, and now that I have my computer working, I need to find a way to connect my hard drive. Western Digital Ide Hard Drive Jumper Settings My System Specs You need to have JavaScript enabled so that you can use this ... They should have some instructions posted.

Once connected, turn on the computer and as the computer is booting, enter BIOS setup.

Click the boot menu. Any suggestions on how to solve this problem? Do you have only one entry in the list there? Why Is It Necessary To Partition The Hard Disk While Installing Operating System? Was this page useful?

Protect the drive from static discharge by wearing a grounded wrist strap. Sukhdev Taneja 12.344 visualizaciones 6:05 How to: Install a Hard Drive into a Desktop - Duración: 7:18. I installed Windows 8.1 64 bit, the trick of using 32bit bootsect.exe worked great. http://apksoftware.com/hard-drive/need-help-transferring-files-from-ide-hard-drive-to-sata-hard-drive.html A problem?

Jumper setting for connect both hard disk and dvd drive on single ide cable Can dvd burner be on a split sata power cable with hard drive Hard Drive vs DVD Verify the drive is enabled in system BIOS. I upgraded from Windows 7 to Windows 10, and now, whenever I restart my computer, it briefly gives a "Boot from CD-Rom" (or some such words to that effect) message, then Yes.

Inicia sesión para añadir este vídeo a la lista Ver más tarde. I am curious why you think a different case would make a difference? Ask a new question Read More Hard Drives Cable DVD Drives Storage Related Resources solved Can't connect DVD rom and HDD hard drive at the same time DVD drive not working Most hard drive manufactures will include these brackets with the hard drive.

Reply Adam August 24, 2016 at 3:49 pm @MikeTek the middle connector is the master, the end is the slave. Set the Jumpers Before installing the hard drive the jumpers must be properly set on the drive itself. Make sure the power is plugged in and everything is connected securely. This guide will work for Windows 7 and Windows 8.  I have a Windows 8 instructable, but it's essentially the same guide with some Windows 8 pictures.  This guide will not

Turn off the power to the host system before installation. Switch to another language: Catalan | Basque | Galician | View all Cerrar Sí, quiero conservarla. I mean, I guess it's that the disk is not "fixed MBR" but I don't know what this means :D Thanks a lot.

I know this is 2 months late but Quote hbenthow Posts : 80 Windows 10 New 29 Mar 2016 #8 OldMike65 said: Read this ...

Then I connect the cable up, bearing in mind that the hard drive as the master should be connected to the centre of the cable, with the slave CD-ROM drive being This is supposed to happen, don't worry. Setting the Jumpers Master or Single Drive - Use this setting if the drive is the only drive on the ATA interface cable. It is running Windows 10.